|
1911 Shop Services
MARS Armament specializes in the modification, repair and refurbishment of Colt 1911 carry guns and service pistols. In-house capabilities include: precision milling, turning and grinding; welding, polishing and abrasive blasting. Our aim is to provide high quality work, personal service and support you can depend on.
Prices are for work on Colt pistols in "New" or "Like New" condition.. |
|
|
General Services |
|
|
Troubleshooting, rate per hour ($10 minimum) |
$50.00 |
|
Test Fire |
$25.00 |
|
Zero weapon includes test target |
$35.00 |
|
Field Strip,clean, inspect and lubricate |
$25.00 |
|
Detail strip, clean, inspect and lubricate |
$42.50 |
|
Detail strip and clean magazines, each |
$5.00 |
|
Reliability Work |
|
|
Colt 1911 Reliability package (Government model)
Careful attention to detail, upgraded parts and hand fitting optimize the inherent reliability of your Colt pistol.
|
$195.00 |
|
Springfield Reliability Package- above work, plus drill and pin ejector, new plunger tube & extractor, 45ACP firing pin barrel relief |
$295.00 |
|
Correctly time barrel |
$25.00+ |
|
Tune and polish bar stock extractor |
$48.00 |
|
Hardened and machined tool steel, oversized firing pin stop |
$35.00 |
|
Colt ejector installed |
$32.50 |
|
Extended ejector, MARS heavy duty, hardened and machined |
$55.00 |
|
Machine frame relief for barrel lower lug clearance |
$15.00 |
|
Open and flare ejection port, relieve inside |
$58.00 |
|
Furnish and install MARS forged plunger tube |
$28.00 |
| Restake plunger tube |
$10.00 |
|
Restake grip bushings |
$15.00 |
|
Colt/Browning style, heavy duty recoil guide and cap |
$28.50 |
|
Trigger Work |
|
|
Trigger job on Colt factory parts (Series 80 add $25.00) |
$85.00 |
|
MARS hardened tool steel sear upgrade (required on pistols with MIM or substandard sear) |
$28.00 |
|
Weld and refit thumb safety as neccesary, with trigger job |
$15.00 |
|
MARS Hard Use Lockwork kit- Koenig hammer, MARS sear/springs/disconnector, new hammer/sear pins, Titanium strut, includes trigger job |
$250.00 |
|
STI carbon fiber/stainless steel trigger, long or short length |
$48.00 |
|
MARS solid aluminum trigger with Integral Overtravel Stop, long short or medium length |
$55.00 |
|
Heinie Lightweight aluminum match trigger- solid aluminum shoe with internal lightening cuts and skeletonized bow |
$55.00 |
|
Competiton trigger job with MARS ultralight lockwork kit- Koenig LW hammer, MARS sear, STI trigger, Ti strut and MS cap, Special sear and mainsprings |
$325.00 |
|
Sight Work |
|
|
NOTE: We are an OEM to Trijicon and can custom machine virtually any sight for Trijicon inserts, with or without white dot. |
|
|
Heinie Sights (Classic or SlantPro) |
$180.00 |
|
Heinie or Novak Low Mount Carry sight set (includes pinned, dovetail front sight, low mount rear sight) |
$165.00 |
|
Heinie Low Mount rear sight, furnished and installed in existing Novak sight cut |
$62.50 |
|
Novak Cross dovetail front sight with tritium insert, (with or without white outline), installed in existing sight cut |
$90.00 |
|
Retro style high profile rear sight installed in factory dovetail; machine slide, furnish and install dovetail front sight |
$125.00 |
|
BoMar BMCS adjustable rear sight, low mounted with hidden rear leaf, (rear sight only) |
$175.00 |
|
Wilson adjustable rear sight low mounted with rear flush to slide on Gold Cup, (includes relocating elevation screw and cross dovetail front sight) |
$275.00 |
| Furnish and install custom Trijicon insert, includes refinish of sight (only). Specify plain or white outline |
$55.00 |
|
Machine slide, furnish and install dovetail front sight with roll pin |
$65.00 |
|
Remove factory dovetail sights and install compatible aftermarket replacement sights, (labor only) |
$35.00 |
|
Machine front sight to narrower profile or open rear notch |
$25.00 |
|
Safeties |
|
|
Brown extended safety- blue or stainless finish; tactical, wide or custom width |
$80.00 |
|
Brown ambidextrous safety- blue or stainless finish; tactical wide or custom width |
$150.00 |
|
TIG weld sear stud and refit |
$25.00 |
|
High grip beavertail, blue or stainless |
$135.00 |
|
S&A high grip beavertail for Springfield, (.220 radius) |
$135.00 |
|
Weld tangs on Springfield to fit Brown/STI/CMC .250 radius beavertail |
$50.00 |
|
Barrel and Slide/Frame fit |
|
|
Barrel bushing, heat treated oversized, heavy duty; fit "hand tight" Blued or stainless finish |
$58.00 |
|
Polish and throat barrel for reliable feeding with hollowpoint ammuniton |
$55.00 |
|
Colt factory "drop in" barrel with MARS oversized OS bushing |
$175.00 |
|
Kart "semi drop in" forged Chromeoly barrel with bushing, link and pin |
$275.00 |
|
Kart forged chromeoly barrel with bushing, link and pin |
$310.00 |
|
Schuemann stainless steel barrel with bushing, link and pin |
$335.00 |
|
Lower barrel bed as required, additional |
$45.00 |
|
Slide to frame fit- weld and machine rails; hand lap and polish |
$225.00 |
|
Crown and polish muzzle |
$28.00 |
|
Magazine Wells |
|
|
Machine bevel magazine well |
$55.00 |
|
Hand blend mag well (done in conjunction with already beveled mag well) |
$45.00 |
|
Furnish and install S&A mag guide, machine blend to frame |
$115.00 |
|
Furnish and install S&A mag guide, hand blend to frame |
$175.00 |
|
Furnish and install Heinie mag well- hand blended to frame with inletted grips |
$275.00 |
|
Point up checkering on S&A guide |
$30.00 |
|
Bevel sides of S&A guide |
$45.00 |
|
Relocate mainspring housing retainer pin hole on S&A guide (for frames with poor fit) |
$50.00 |
|
Metalwork |
|
| Blend rear of slide and extractor, hand serrate @ 40 or 50 LPI (requires oversized firing pin stop) |
$55.00 |
|
Dehorn sharp edges of pistol |
$95.00 |
|
Machine border on slide |
$95.00 |
|
Machine bevel on bottom of slide |
$55.00 |
|
Flatten top of slide |
$60.00 |
|
Flatten slide stop pin |
$28.00 |
|
Machine forward cocking serrations- Colt Government style |
$85.00 |
|
Machine forward cocking serrations- Colt GoldCup/XSE style |
$115.00 |
|
Snakeskin front strap and flat mainspring housing (includes barstock housing, true and high cut front strap and housing ) |
$325.00 |
|
Scallop front strap and flat mainspring housing (includes barstock housing, true and high cut front strap and housing ) |
$250.00 |
|
Golf Ball front strap and flat mainspring housing (includes barstock housing, true and high cut front strap and housing ) |
$285.00 |
|
Checker frontstrap and mainspring housing (includes barstock housing, true and high cut front strap and housing) 20, 25 or 30LPI |
$375.00 |
|
Serrate frontstrap and flat mainspring housing - Gold Cup/Combat Elite style @ 20 or 30 LPI (includes barstock housing, true and high cut front strap and housing ) |
$175.00 |
|
add S&A "drop in" mag guide to above |
$48.00 |
|
Snakeskin, Scallop, Golf Ball or Serrate S&A guide, (includes truing guide) add to above prices |
$75.00 |
|
True frontstrap and relieve for high grip |
$95.00 |
|
Blend mainspring housing to frame and true |
$35.00 |
|
add 25% to above for stainless steel |
|
|
Finishes |
|
|
Manganese phosphate complete pistol, abrasive blasted finish per mil spec. |
$125.00 |
|
Manganese phosphate complete pistol, soft glass bead blast finish. |
$155.00 |
|
Ceracote complete pistol |
$255.00 |
|
Satin Hard chrome finish (flats and lines detailed and trued) |
$295.00 |
|
Matte black oxide finish complete pistol |
$125.00 |
|
Satin black oxide finish complete pistol (fine glass bead blast) |
$150.00 |
|
Black oxide finish with 400grit Hand polished flats and matte rounds |
$225.00 |
|
Detail pistol- true lines, polish toolmarks, remove rust/pitting/scratches, etc, minimum |
$35.00 |
|
Refinish small parts, any finish (chrome, oxide, phosphate, Ceracote), each |
$15.00 |
|
Specialty Services and Repairs |
|
|
Dawson light rail furnished and installed (includes installing Dawson mount adaptor onto your SureFire light) |
$160.00 |
|
Drill and tap magazine, install hard rubber base pad |
$9.00 |
|
Fit grips |
$15.00 |
|
Fit grips for ambidextrous safety |
$20.00 |
|
Remove stripped grip bushing, ream and tap frame, bond and stake oversized replacement bushing,
Each additional (concurrent with the first) $10.00 |
$15.00 |
|
TiG welding, minimum charge |
$15.00 |
|
Surface grind slide flats |
$79.50 |
|
Machine aluminum frame and install hardened steel insert, machine and polish feedramp |
$125.00 |